A needle gun has a set of very fine chisels known as needles. The tool forces these needles against a work surface at variable speeds up to around 5,000 times per minute. Different models offer choices of number of needles, operating speed, and power levels. Many models use compressed air, although electrical needle-guns do exist.
In a pneumatic unit, compressed air forces a piston forwards and backwards. This movement causes the needles to move back and forth against the work surface.
An able seaman uses a needlegun to remove scale while refurbishing a mooring winch.
The needle gun has advantages over other scaling tools. Its main advantage is that the needles automatically adjust themselves to contours, making the tool a good choice for cleaning irregular surfaces. A needle gun can clean an area to bare metal in seconds, and compares well to other scaling tools in terms of accuracy and precision.
It is recommended that before needlegunning, a surface be prepared by removing oil, grease, dirt, chemicals and water-soluble contaminants. This can be done with solvents or with a combination of detergent and fresh water.
Then, the needle gun is used to remove rust, loose mill scale and paint, leaving bare metal. It is used most effectively by holding it at a 90 angle to the work surface. It is recommended that an area no larger than six to eight inches be cleared at once. Two to three passes over an area is generally sufficient to clean it. Then the process is repeated until the desired area is completed.
Prior to painting, it is desirable to feather any edges between metal and old paint. It is also important to check the surface for oil deposited during chipping, and if necessary, clean the area with solvents. Since bare metal surfaces will flash rust soon after exposure to the atmosphere, paint should be applied as soon as possible after chipping. If flash rusting occurs prior to coating, further chipping, cleaning and sanding may be necessary.
See also
Nautical portal
Abrasive blasting
Corrosion
Rust
Wire brush
Notes
^ U.S. Navy, 2006.
^ a b c d e f g h Miller, 2008.
^ Park, 1984.
^ a b c d e f g h i j k l NAVSEA, 2008.
^ a b c NETC, 2003, p. 11-10.
^ Nitto Kohki, 2008.
References
Miller, Jason (2008-01-30). "Needle Scaler and Debris Removal". Free Online Library. Free Online Library. http://www.thefreelibrary.com/Needle+Scaler+and+Debris+Removal-a01073853851. Retrieved 2008-04-05.
Naval Sea Systems Command (NAVSEA) (2008). "Chapter 7: Submarine Forces Afloat Painting and Preservation Guidelines for Non-Nuclear Spaces and Components". Contracted Ship Maintenance. Joint Fleet Maintenance Manual - Rev A Change 7. VI. United States Navy. http://www.submepp.navy.mil/jfmm/HTML/Volume VI/VI-Ch-07.htm.
Naval Education and Training Command (NETC) (2003) . "Chapter 11: Painting". NAVEDTRA 14343: Boatswain's Mate. Nonresident Training Manuals. Pensacola, Florida: United States Navy. http://www.navystorekeeper.com/NAVEDTRA_14343.pdf. Retrieved 2008-04-05.
Park, Sharon (1984). "#13: The Repair and Thermal Upgrading of Historic Steel Windows". Preservation Briefs. Government Publishing Office. http://w3.gsa.gov/web/p/HPTP.NSF/a533f1f859737bc9852565cc0058d0b6/064f66fe515200ca852565c50054b2ff?OpenDocument. Retrieved 2008-04-05.
Nitto Kohki (2008). "EJC-32A Electric Needle Scaler". nittokohki.com. Nitto Kohki USA. http://www.nittokohki.com/tools/products/powertools/needlescalers/ejc-32a.html. Retrieved 2008-04-05.
U.S. Navy (2006-03-23). "Eye on the Fleet". Navy NewsStand. United States Navy. http://www.navy.mil/view_single.asp?id=33020. Retrieved 2008-04-05.
External links
Video of needle-gunning rust
Battleship Texas Restoration Manual
Safety while removing paint
Schematic and parts list for Jet Chisel JT-20
v d e
Metalworking
Tools
Cutting machines
Water jet cutter Band saw Cold saw Laser Miter saw Plasma
Cutting tools
Broach Burr Chisel Counterbore Countersink End mill File Guillotine shear Hand scraper Milling cutter Nibbler Reamer Throatless shear Tipped tool Tool bit
Forming tools
Brake Die English Wheel Flypress Hydraulic press Machine press Punch press Stamping press
Hand tools
Clamp Combination square Drift pin File card Hacksaw Hammer Hand scraper Machinist square Magnetic base Needlegun scaler Pipe and tube bender Pliers Punch Saw piercing Scriber Tap and die Tongs Vise Workbench Wrench
Machine tooling
Angle plate Chuck Collet Jig Fixture Indexing head Lathe center Machine taper Magnetic base Mandrel Rotary table Wiggler
Measuring instruments
Bore gauge Caliper Comparator Dial indicator Engineer's blue Feeler Center gauge and fishtail gauge Gauge block Gauge Go-NoGo Machinist square Marking blue Marking gauge Marking out Micrometer Radius gauge Scale Sine bar Spirit level Straightedge Surface plate Tape measure Thread pitch Height gauge Vernier scale Wiggler
Smithing tools
Anvil Forge Fuller Hardy hole Hardy tools Pritchel Slack tub Steam hammer Swage block Trip hammer
Casting Fabrication Forming Jewellery Machining Metallurgy Smithing Tools & Terminology Welding
Categories: Cleaning tools | Metalworking hand tools
About the Author:
I am a professional writer from China Manufacturers, which contains a great deal of information about copper carbonate , manganese dioxide, welcome to visit!
Author: sisi
